Supporto da vuoto MultiScreenHTS
Risorse correlate
Prodotti consigliati
Panoramica
Specifiche tecniche
Informazioni per l’ordine
Documentation
Riferimenti bibliografici
| Panoramica dei riferimenti bibliografici | Applicazione |
|---|---|
| Method for Simultaneous Measurement of Antibodies to 23 Pneumococcal Capsular Polysaccharides Raymond Biagini, Sonela Schlottmann, Deborah Sammons, Jerome Smith, John Snawder, Cynthia Striley, Barbara MacKenzie, and David Weisssman Clinical and Diagnostic Laboratory Immunology September 2003, p 744-750, Vol. 10, No. 5 2003 | |
| A non-radiolabelled ferriprotoporphyrin IX biomineralisation inhibition test for the high throughput screening of antimalarial compounds. E. Deharo, R. N. Garcia, P. Oporto, A. Gimenez, M. Sauvain, V. Jullian and H. Ginsburg Experimental Parasitology 100 (4): 252-256 2002 | |
| High-Throughput Microplate Format for Producing and Screening Riboprobes from Bacterial Cells Matthews, P.D. and Wurtzel, E.T. BioTechniques. 18: 6, 1000 – 1004 1994 | Nucleic Acid Purification and Concentration |
| Use of Multiscreen plates for the preparation of bacterial DNA suitable for PCR Reek FH, Smits MA, Kamp EM, Smith HE Biotechniques. 1995 Aug;19(2):282-5 1994 | PCR |
FAQ
| Domanda | Risposta |
|---|---|
| Can I alcohol sterilize my Multiscreen Manifold and Plates? | Note: This procedure does not work for the nitrocellulose based membrane plates such as HATF. (For use on: Durapore PVDF, Biopore, and glass fiber filters). MultiScreen Alcohol Sterilization Protocol Additional Materials Required: 1. 70% Reagent grade ethanol (with NO added denaturation agents) 2. Suitable sterile support or container to place the plate(s) inside or alternatively on for incubation. A sterile material such as a lid can be used, although the support trays supplied with pre-sterilized MultiScreen plates are ideal. 3. Sterilized water or buffer. 4. Sterilized (5x9” or 4x6”) gauze or sponges for blotting the underdrain. Procedure (To be performed in Laminar flow hood under aseptic conditions): 1. Thoroughly rinse, fill, and expose all surfaces of the Vacuum manifold to 70% Alcohol and incubate 5-15 minutes. Turn on vacuum to remove excess alcohol. 2. Place MultiScreen plate to be sterilized on top of the vacuum manifold and completely fill with 70% alcohol. Be careful to expose all surfaces to the alcohol and allow to incubate 5-15 minutes. Additional plates can be sterilized by placing on a lid or other suitable object during incubation. 3. Turn on vacuum to remove excess alcohol, tip plate to drain excess alcohol into vacuum manifold, blot on sterilized pad, and place on lid to air dry overnight in laminar flow hood. 4. Turn on vacuum and remove all of the alcohol, add sterilized water to inside of manifold to remove residual alcohol. Allow entire unit such as the steel support and gasket to air dry under the hood with the top removed. The manifold can be stored in the hood and used as required. Note: The MultiScreen lids can also be sterilize by this procedure. Cautions: 1. Do not allow alcohol to remain inside vacuum manifold, it should be rinsed each day with sterile water. 2. This procedure does not work for the nitrocellulose based |
| I broke the tubing adapter on my MultiScreen manifold. Is there a replacement part? | Yes, this piece can be purchased as part of the Repair Kit, catalog # MAVMXXA03. It's important to point out that in many cases a broken adapter result from improperly cared for manifolds. Always rinse manifold with water after its use in an assay (especially TCA precipitation assays). |
| What plates are compatible with the MultiScreen manifold? | In general, all manufacturers' plates fit the vacuum manifold. |
| I’m not getting good vacuum while using the MultiScreen vacuum manifold, what can I do? | Press down on the MultiScreen plate to form a good seal with the manifold. (This is normal for the low vacuum used). Make sure all wells of the filter plate are either “wet” or sealed with adhesive tape. Check all tubing connections to make sure they are tight. See the MultiScreen Vacuum manifold operators guide for more detailed troubleshooting information. |
| What plates can be used with the MultiScreen HTS manifold (Catalogue number MSVMHTS00)? | All MultiScreen HTS platform filter plates, Solvinert and Solvinert Deep Well plates can be used with the HTS manifold. |
| Can the classic MultiScreen plates be run on the HTS manifold? | Only in filter to waste mode. The HTS plates should be used with the HTS manifold for the most benefit. |
| Can the MultiScreen HTS manifold be used with Millipore's genomics application plates (plamid prep, pcr cleanup, sequence reaction clean up)? | Filter to waste modes work, but not filtrate collection, so using the clearing plate with the plamid plate will not work. Millipore's genomics plates have not been validated on the HTS manifold. Please contact technical service for more information at 1-800-645-5476. |
| If using the MultiScreen HTS manifold, when do I have to use the droplet trap array? | The droplet trap array should be used when filtering a 384 well plate to waste. |
| If the deep well collar sold with the MultiScreen HTS manifold or is it sold seperately? | The deep well collar is sold as an accessory to the MultiScreen HTS manifold; it does not come with the manifold. The catalogue number is MSVMHTS0D. |
| When using the MultiScreen HTS manifold, can I filter to waste when using a shallow well plate? | Yes. The classic grid should be in place for removeable underdrain HTS plates or the collar gasket frame should be in place for Solvinert plates. |
Prodotti e applicazioni correlate
Linee di prodotti
Filtri MillexI filtri Millex con membrana Fluoropore idrofoba sono ideali per la filtrazione.Per saperne di più >> |
Prodotti correlati per: Application Facete
| Protein Purification |
| Sample Preparation |
| Dialysis and Filtration |
Prodotti correlati per: Brand Facete
| MultiScreen™ |
Categorie
| Life Science Research > Cell Culture and Systems > Cell Culture Flasks, Plates, & Slides > Multiwell Plates |
)